cBN-Fe磁性磨粒的制备工艺及性能

马雨寒; 张宝瑞; 周长乐; 陈保池; 王大庆; 田鑫; 丁云龙

doi:10.13394/j.cnki.jgszz.2022.0130

cBN-Fe磁性磨粒的制备工艺及性能

doi: 10.13394/j.cnki.jgszz.2022.0130

辽宁科技大学机械工程与自动化学院, 辽宁鞍山 114051

基金项目: 辽宁省教育厅科学研究经费（2019LNQN01）；辽宁省科技厅博士启动经费（2021-BS-241）。

详细信息

作者简介:
丁云龙，男，1988年生，博士、副教授。主要研究方向：精密加工与特种加工。E-mail：dylustl@163.com

中图分类号: TG73; TG58; TQ164
计量
- 文章访问数: 393
- HTML全文浏览量: 163
- PDF下载量: 37
- 被引次数: 0
出版历程
- 收稿日期: 2022-08-15
- 修回日期: 2022-11-30
- 录用日期: 2022-12-09
- 刊出日期: 2023-08-30

Preparation process and performances of cBN-Fe magnetic abrasive particles

School of Mechanical Engineering and Automation, University of Science and Technology, Anshan 114051, Liaoning, China

摘要

摘要:
针对现有烧结法制备的磁性磨粒中研磨相材料硬度较低，对硬度高、导磁性差的钛合金等工件的研磨效果差，且硬度最高的金刚石材料无法作为研磨相用烧结法来制备磁性磨粒的问题，以Fe粉为基体，cBN粉末为研磨相，烧结制备cBN-Fe磁性磨粒；以Ti-6A1-4V（TC4）板为研磨对象，用控制变量法探究烧结法制备的cBN-Fe磁性磨粒中烧结时间、升温速度、原料配比对其研磨性能的影响，确定其最佳的制备工艺参数；并以45^#钢和202不锈钢为研磨工件，比较cBN-Fe与烧结法制备的Al₂O₃-Fe、SiC-Fe 3种磁性磨粒研磨前后工件的表面粗糙度、表面形貌，探究不同磁性磨粒的研磨性能和使用寿命。结果表明：当Fe粉与cBN粉的质量比为3∶1，烧结温度为1150 ℃，烧结时间为6 h，保温时间为2 h，升温速度为3.19 ℃/min时，制备的cBN-Fe磁性磨粒研磨性能最佳，优于烧结法制备的Al₂O₃-Fe、SiC-Fe磁性磨粒的，且其使用寿命分别是Al₂O₃-Fe磁性磨粒和SiC-Fe磁性磨粒的1.6倍和1.3倍。
- 烧结法 /
- 磁性磨粒 /
- 升温速度 /
- 原料配比
Abstract:
In order to solve the problems of low hardness in the grinding phase material of magnetic abrasive particles prepared by the existing sintering method, the grinding effects on high-hardness and poor magnetic conductivity materials, such as titanium alloys, were found to be poor. Additionally, the hardest diamond material could not be used as the grinding phase to prepare magnetic abrasive particles by the sintering method. In this study, the cBN-Fe magnetic abrasive particles were prepared by sintering with Fe powder as the matrix and cBN powder as the grinding phase. The study focused on using Ti-6A1-4V (TC4) plates as the grinding objects, and the effects of sintering time, heating rate and raw material ratio on the grinding performances of cBN-Fe magnetic abrasive particles were explored using a control variable method. The aim was to determine the optimal preparation process parameters of cBN-Fe magnetic abrasive particles. Taking 45^# steel and 202 stainless steel as grinding workpieces, the performance of cBN-Fe magnetic abrasive particles were compared with that of Al₂O₃-Fe and SiC-Fe magnetic abrasive particles, both prepared by the sintering method. The surface roughness and morphology of the workpieces before and after grinding with three kinds of magnetic abrasive particles were compared. Moreover, the grinding performance and service life of different magnetic abrasive particles were investigated. The results show that the best grinding performances for cBN-Fe magnetic abrasive particles was achieved when using a mass ratio of Fe powder to cBN powder of 3∶1, a sintering temperature of 1150 ℃, a sintering time of 6 h, a holding time of 2 h and a heating rate of 3.19 ℃/min. Furthermore, it is found that the grinding performance of cBN-Fe magnetic abrasive particles is better than that of Al₂O₃-Fe and SiC-Fe magnetic abrasive particles prepared by sintering. The service life of cBN-Fe magnetic abrasive particles is 1.6 times and 1.3 times longer than that of Al₂O₃-Fe and SiC-Fe magnetic abrasive particles, respectively.
- sintering method /
- magnetic abrasive particles /
- heating rate /
- raw material ratio

HTML全文

图 1 烧结法制备磁性磨粒流程图

Figure 1. Flow chart of preparation of magnetic abrasive particles by sintering

下载: 全尺寸图片幻灯片

图 2 磁粒研磨光整加工装置

Figure 2. Magnetic abrasive finishing device

下载: 全尺寸图片幻灯片

图 3 磁性磨粒不同体积占比示意图

Figure 3. Schematic diagram of different volume proportions of magnetic abrasive particles

下载: 全尺寸图片幻灯片

图 4 磁性磨粒产量与废料比例关系

Figure 4. Relationship between magnetic abrasive grain yield and waste ratio

下载: 全尺寸图片幻灯片

图 5 磁性磨粒的原子质量分数和能谱分析图

Figure 5. Atomic mass fraction and energy spectrum analysis of magnetic abrasive particles

下载: 全尺寸图片幻灯片

图 6 原料配比对工件表面粗糙度的影响

Figure 6. Effect of raw material ratios on surface roughness of workpiece

下载: 全尺寸图片幻灯片

图 7 研磨前后TC4的表面微观形貌

Figure 7. Surface micro morphology of TC4 before and after grinding

下载: 全尺寸图片幻灯片

图 8 不同烧结时间下烧结的坯体形貌

Figure 8. Morphologies of green bodies sintered at different sintering times

下载: 全尺寸图片幻灯片

图 9 加工时间对工件表面粗糙度的影响

Figure 9. Influence of machining time on surface roughness of workpiece

下载: 全尺寸图片幻灯片

图 10 研磨后TC4表面微观形貌

Figure 10. Surface micro morphology of TC4 after grinding

下载: 全尺寸图片幻灯片

图 11 磁性磨粒的磁化曲线

Figure 11. Magnetization curves of magnetic abrasive particles

下载: 全尺寸图片幻灯片

图 12 45^#钢表面粗糙度随时间的变化

Figure 12. Variation of surface roughness of 45^# steel with times

下载: 全尺寸图片幻灯片

图 13 45^#钢研磨前后的表面微观形貌

Figure 13. Surface morphology of 45^# steel before and after grinding

下载: 全尺寸图片幻灯片

图 14 磁性磨粒寿命对比分析

Figure 14. Comparative analysis of magnetic abrasive life

下载: 全尺寸图片幻灯片

表 1 试验条件

Table 1. Experimental condition

参数	取值
SH-190水基研磨液体积 V / mL	5
主轴转速 n₁ / ( r·min⁻¹)	1 500
工件进给速度 v_w / (mm·s⁻¹)	1
工件转速 n₂ / ( r·min⁻¹)	10
加工间隙 d / mm	2

下载: 导出CSV

表 2 3种磁性磨粒制备参数

Table 2. Three preparation parameters of magnetic abrasive particles

参数名称	取值
cBN-Fe质量比 R₁	3∶1
SiC-Fe、Al₂O₃-Fe质量比 R₂	2∶1
cBN-Fe压制力 p₁ / kN	90
SiC-Fe压制力 p₂ / kN	110
Al₂O₃-Fe压制力 p₃ / kN	75
cBN-Fe、SiC-Fe烧结温度 θ₁ / ℃	1 150
Al₂O₃-Fe烧结温度 θ₂ / ℃	1 200
cBN-Fe、SiC-Fe、Al₂O₃-Fe烧结时间 t₁ / h	6
cBN-Fe、Al₂O₃-Fe保温时间 t₂ / h	2
SiC-Fe保温时间 t₃ / h	3

下载: 导出CSV

表 3 3种磁性磨粒铁磁性能对比

Table 3. Comparison of ferromagnetic properties of three kinds of magnetic abrasive grains

名称	饱和磁化强度 M_s /（emu·g⁻¹）	矫顽力 H_c / Oe
cBN-Fe	133.1	52.4
SiC-Fe	92.2	45.7
Al₂O₃-Fe	75.7	93.6

下载: 导出CSV

参考文献(22)

[1]	SHINMURA T, TAKAZAWA K, HATANO E, et al. Study on magnetic abrasive finishing [J]. CIRP Annals,1990,39(1):325-328. doi: 10.1016/S0007-8506(07)61064-6
[2]	SHINMURA T, YAMAGUCHI H. Study on a new internal finishing process by application magnetic abrasive machining (internal finishing of stainless steel tube and clean gas bombs) [J]. Transactions of the Japan Society of Mechanical Engineering Series C,1993,59(560):1261-1267. doi: 10.1299/jsmec1993.38.798
[3]	SHINMURA T, AIZAWA T. Study on internal finishing of a non-ferromagnetic tubing by magnetic abrasive machining process [J]. Bulletin of the Japan Society of Precision Engineering,1988,54(4):767-773. doi: 10.2493/jjspe.54.767
[4]	白旭. 磁性磨粒的溶胶—凝胶法制备工艺及其性能研究 [D]. 太原: 太原理工大学, 2019. BAI Xu. Preparation and properties of magnetic abrasive particles by sol-gel method [D]. Taiyuan: Taiyuan University of Technology, 2019.
[5]	张旭. 烧结磁性磨料制备过程分析及工艺优化 [D]. 鞍山: 辽宁科技大学, 2013. ZHANG Xu. Mechanism study and process control of sintering magnetic abrasive [D]. Anshan: Liaoning University of Science and Technology, 2013.
[6]	张桂香. 雾化快凝磁性磨料制备及其磁力光整加工性能研究 [D]. 南京: 南京航空航天大学, 2012. ZHANG Guixiang. Study on preparation of magnetic abrasives by gas atomization with rapid solidification and their finishing performance [D]. Nanjing: Nanjing University of Aeronautics and Astronautics, 2012.
[7]	KOTARO H, HITOMI Y. Development of spherical iron-based composite powder with carried alumina abrasive grains by plasma spray [J]. Advanced Materials Research,2009,75:43-46.
[8]	张春宇. 化学复合镀法制备磁性磨料工艺研究 [D]. 大连: 大连理工大学, 2014 ZHANG Chunyu. Study on process of magnetic abrasive grains with electroless composite plating method [D]. Dalian: Dalian University of Technology, 2014.
[9]	潘韩飞. 金刚石磁性磨料的制备及其磁控研磨加工性能研究 [D]. 南京: 南京航空航天大学, 2016. PAN Hanfei. Research on the preparation of diamond magnetic abrasive and its finishing performance [D]. Nanjing: Nanjing University of Aeronautics and Astronautics, 2016.
[10]	牛凤丽, 陈燕, 张旭, 等. 铁基白刚玉磁性磨料的制备工艺与磨削性能研究 [J]. 兵器材料科学与工程,2015,38(6):35-40. doi: 10.14024/j.cnki.1004-244x.20151028.004 NIU Fengli, CHEN Yan, ZHANG Xu, et al. Preparation process and grinding performance of iron-based white alumina magnetic abrasive particles [J]. Ordnance Material Science and Engineering,2015,38(6):35-40. doi: 10.14024/j.cnki.1004-244x.20151028.004
[11]	康璐, 陈燕, 严正伟, 等. SiC-Fe磁性研磨粒子的制备工艺和研磨性能研究 [J]. 兵器材料科学与工程,2018,41(4):53-57. doi: 10.14024/j.cnki.1004-244x.20180611.001 KANG Lu, CHEN Yan, YAN Zhengwei, et al. Preparation process and grinding properties of SiC-Fe magnetic abrasive particles [J]. Ordnance Material Science and Engineering,2018,41(4):53-57. doi: 10.14024/j.cnki.1004-244x.20180611.001
[12]	贺美云. 磁性磨料的烧结法制备及其加工特性的分析研究 [D]. 太原: 太原理工大学, 2003. HE Meiyun. The analysis and research on sintering preparation and finishing characteristic of magnetic abrasive grains [D]. Taiyuan: Taiyuan University of Technology, 2003.
[13]	贺美云, 王建新, 张银喜. 烧结法制备磁性磨料的实验研究 [J]. 航空精密制造技术,2010,46(6):43-45. doi: 10.3969/j.issn.1003-5451.2010.06.011 HE Meiyun, WANG Jianxin, ZHANG Yinxi. Experimental research on sintering preparation of magnetic abrasive grains [J]. Aviation Precision Manufacturing Technology,2010,46(6):43-45. doi: 10.3969/j.issn.1003-5451.2010.06.011
[14]	邵华丽, 王海阔, 徐三魁, 等. 聚晶金刚石的热稳定性研究进展 [J]. 材料导报,2015(15):81-84, 102. SHAO Huali, WANG Haikuo, XU Sankui, et al. Research progress of thermal stability for polycrystalline diamond [J]. Materials Review,2015(15):81-84, 102.
[15]	涂禄强, 徐锋, 田帅, 等. 立方氮化硼涂层刀具制备及切削性能研究现状 [J]. 机械制造与自动化,2020(1):16-19. doi: 10.19344/j.cnki.issn1671-5276.2020.01.005 TU Luqiang, XU Feng, TIAN Shuai, et al. Recent advances under study of deposition and cutting performance of cubic boron nitride cutting tools [J]. Mechanical Manufacturing and Automation,2020(1):16-19. doi: 10.19344/j.cnki.issn1671-5276.2020.01.005
[16]	JAROSZ K, UKAR E, KRDEL A, et al. Laser ablation and processing of polycrystalline cubic boron nitride cutting tool material [J]. The International Journal of Advanced Manufacturing Technology, 2022, 118(3/4): 785-800.
[17]	肖作义. 磁力研磨光整加工技术的试验研究 [J]. 模具工业,2004(12):47-50. doi: 10.3969/j.issn.1001-2168.2004.12.015 XIAO Zuoyi. Experimental study on magnetic abrasive finishing technology [J]. Mold Industry,2004(12):47-50. doi: 10.3969/j.issn.1001-2168.2004.12.015
[18]	YAMAGUCHI H, SHINMURA T. Study of an internal magnetic abrasive finishing using a pole rotation system: Discussion of the characteristic abrasive behavior [J]. Precision Engineering,2000,24(3):237-244. doi: 10.1016/S0141-6359(00)00037-4
[19]	陈燕, 巨东英. 磁研磨法对微型阶梯轴表面的抛光处理 [J]. 模具制造,2004(12):48-51. doi: 10.3969/j.issn.1671-3508.2004.12.022 CHEN Yan, JU Dongying. Polishing of micro stepped shaft surface by magnetic abrasive method [J]. Mold Manufacturing,2004(12):48-51. doi: 10.3969/j.issn.1671-3508.2004.12.022
[20]	JIAO A, QUAN H, LI Z, et al. The study of plane magnetic abrasive finishing based on axial pressure [J]. International Journal of Machining and Machinability of Materials,2015,17(5):418-433. doi: 10.1504/IJMMM.2015.073150
[21]	陈燕, 周锟, 牛凤丽, 等. 航空发动机整体叶盘磁力研磨光整试验 [J]. 航空动力学报,2015,30(10):2323-2330. CHEN Yan, ZHOU Kun, NIU Fengli, et al. Experiment of surface finishing on aero-engine blisk by magnetic abrasive finishing [J]. Journal of Aerospace Power,2015,30(10):2323-2330.
[22]	牛凤丽. 磁力研磨中研磨介质的性能分析及试验研究 [D]. 鞍山: 辽宁科技大学, 2015. NIU Fengli. Performance analysis of grinding media in magnetic abrasive finishing and experiment research [D]. Anshan: Liaoning University of Science and Technology, 2015.